Betekenis van:
closing off

Werkwoord

Voorbeeldzinnen

1. For a shut-off valve, the closing torque is to be consistent with the size of handwheel, wrench, or other means employed to operate the valve.
2. The glasshouse shall consist of a permanent structure with a continuous waterproof covering, located on a site graded to prevent entry of surface-water run-off, and with self-closing lockable doors.
3. The plans provide for the reduction of capacities, the hive-off of company property, the closing of unprofitable subsidiaries, the reduction of negative operating results, measures to reduce costs and optimise distribution and the search for a strategic partner.
4. Toys and their parts must not present a risk of asphyxiation by closing off the flow of air as a result of airway obstruction external to the mouth and nose.
5. When the 80 per cent stop valve does not comprise any float, it shall not be possible to continue filling, after closing-off, at a rate exceeding 500 cm3/minute.
6. The concession agreement provided that the State would compensate AVR financially for the remaining book value of investments carried out in favour of AVR-Nuts during the period covered by the agreement with the approval of the State but not yet written off. Applying this clause in advance, the Dutch authorities calculated compensation of €8670108 for the costs of closing down the first RDF.
7. A cut-off time for customer payments (both domestic and cross-border) of one hour before the normal TARGET closing time will apply; the remaining time will be used only for interbank payments (both domestic and cross-border) to transfer liquidity between participants.
8. Toys and their parts must be of such dimensions as to not present a risk of asphyxiation by closing off the flow of air as a result of internal airway obstruction by objects wedged in the mouth or pharynx or lodged over the entrance to the lower airways.
9. A manometer or calibrated pressure gauge of the retard type, which will permit readings in the range of 0 to 1440 kPa is to be connected to a pressure take-off on the upstream side of the test sample to indicate the closing pressure.
10. A cut-off time for customer payments (both domestic and cross-border of one hour before the normal TARGET closing time will apply; the remaining time will be used only for interbank payments (both domestic and cross-border to transfer liquidity between participants.
11. These insolvency plans are the restructuring or rather the recapitalisation plans (Sanierungspläne) of the Herlitz Group. The plans provide for the reduction of capacities, the hive-off of company property, the closing of unprofitable subsidiaries, the reduction of negative operating results, measures to reduce costs and optimise distribution and the search for a strategic partner.
12. All protection devices which are used to prevent damage to the power source in the case of an overload or stalling shall reset themselves after the overload or the automatic switch off. After resetting of the protection devices, the motion in the closing direction shall not resume without a deliberate action on the control device.
13. The Icelandic authorities considered that the valuation of the assets in Reykjavik was very favourable to the State since they had a strategic value, based on projected future value, ‘since plans were at the time of sale being made for a large bridge project closing off the Company’s harbour at Saeverhöfdi in Reykjavik and thus rendering the facilities useless for the operations of the Company.
14. Make(s):4.3.2.4.2. Type(s):4.3.2.4.3. Speed at which cut-off starts under full load (2): … r/min4.3.2.4.4. Maximum no-load speed (2): … r/min4.3.2.4.5. Idling speed (2): … r/min4.3.3. Cold-start system4.3.3.1. Make(s):4.3.3.2. Type(s):4.3.3.3. Description:4.4. Valve timing4.4.1. Maximum lift and opening and closing angles in relation to top dead centre or equivalent data:4.4.2. Reference clearances and/or setting ranges (1):4.4.3. Variable valve timing system (if applicable and where intake and/or exhaust)4.4.3.1. Type: continuous or on/off4.4.3.2. Cam phase shift angle:4.5. Porting configuration4.5.1.
15. Make(s):4.3.2.4.2. Type(s):4.3.2.4.3. Speed at which cut-off starts under full load (2): … r/min4.3.2.4.4. Maximum no-load speed (2): … r/min4.3.2.4.5. Idling speed (2): … r/min4.3.3. Cold-start system4.3.3.1. Make(s):4.3.3.2. Type(s):4.3.3.3. Description:4.4. Valve timing4.4.1. Maximum lift and opening and closing angles in relation to top dead centre or equivalent data:4.4.2. Reference clearances and/or setting ranges (1):4.4.3. Variable valve timing system (if applicable and where intake and/or exhaust)4.4.3.1. Type: continuous or on/off4.4.3.2. Cam phase shift angle:4.5. Porting configuration4.5.1. Position, size and number:4.6. Electronic command functionsIf the engine features electronically controlled functions, information concerning their performance must be provided including:4.6.1. Make:4.6.2. Type:4.6.3. Part number:4.6.4. Location of engine electronic control unit:4.6.4.1. What does it sense:4.6.4.2. What does it control: ’;