Betekenis van:
top off

Voorbeeldzinnen

1. Take this knife and cut the top off.
2. And, to top it all off, he can read Hebrew.
3. The third (group of) company(-ies) claimed that the tax benefit they enjoyed is not applicable anymore since 1 January 2008 and that it was a one-off tax reduction scheme that could not have any impact on the company costs in the following years and that on top of it the tax exemption was very minor.
4. The shares are then to be cumulated, starting with the largest, until a cut-off level of 90 % is reached. All metiers belonging to the top 90 % shall be selected for sampling, the exercise shall then be repeated according to the total value of the commercial landings and repeated a third time according to the total effort in days-at-sea.
5. The shares are then to be cumulated, starting with the largest, until a cut-off level of 90 % is reached. All metiers belonging to the top 90 % shall be selected for sampling, The exercise shall then be repeated according to the total value of the commercial landings and repeated a third time according to the total effort in days-at-sea.
6. Make(s):4.3.2.4.2. Type(s):4.3.2.4.3. Speed at which cut-off starts under full load (2): … r/min4.3.2.4.4. Maximum no-load speed (2): … r/min4.3.2.4.5. Idling speed (2): … r/min4.3.3. Cold-start system4.3.3.1. Make(s):4.3.3.2. Type(s):4.3.3.3. Description:4.4. Valve timing4.4.1. Maximum lift and opening and closing angles in relation to top dead centre or equivalent data:4.4.2. Reference clearances and/or setting ranges (1):4.4.3. Variable valve timing system (if applicable and where intake and/or exhaust)4.4.3.1. Type: continuous or on/off4.4.3.2. Cam phase shift angle:4.5. Porting configuration4.5.1.
7. Make(s):4.3.2.4.2. Type(s):4.3.2.4.3. Speed at which cut-off starts under full load (2): … r/min4.3.2.4.4. Maximum no-load speed (2): … r/min4.3.2.4.5. Idling speed (2): … r/min4.3.3. Cold-start system4.3.3.1. Make(s):4.3.3.2. Type(s):4.3.3.3. Description:4.4. Valve timing4.4.1. Maximum lift and opening and closing angles in relation to top dead centre or equivalent data:4.4.2. Reference clearances and/or setting ranges (1):4.4.3. Variable valve timing system (if applicable and where intake and/or exhaust)4.4.3.1. Type: continuous or on/off4.4.3.2. Cam phase shift angle:4.5. Porting configuration4.5.1. Position, size and number:4.6. Electronic command functionsIf the engine features electronically controlled functions, information concerning their performance must be provided including:4.6.1. Make:4.6.2. Type:4.6.3. Part number:4.6.4. Location of engine electronic control unit:4.6.4.1. What does it sense:4.6.4.2. What does it control: ’;
8. Fuel feed3.2.3.1. Feed pumpPressure (2) or characteristic diagram: kPa3.2.3.2. Injection system3.2.3.2.1. Pump3.2.3.2.1.1. Make(s):3.2.3.2.1.2. Type(s):3.2.3.2.1.3. Delivery: mm3 (2) per stroke or cycle at pump speed of: r/min (rated) and r/min (maximum torque), respectively, or characteristic diagramState which method is used: on engine/on pump bench (1)3.2.3.2.1.4. Injection advance3.2.3.2.1.4.1. Injection advance curve (2):3.2.3.2.1.4.2. Timing (2):3.2.3.2.2. Injection piping3.2.3.2.2.1. Length: mm3.2.3.2.2.2. Internal diameter: mm3.2.3.2.3. Injector(s)3.2.3.2.3.1. Make(s):3.2.3.2.3.2. Type(s):3.2.3.2.3.3. Opening pressure (2) or characteristic diagram:3.2.3.2.4. Governor3.2.3.2.4.1. Make(s):3.2.3.2.4.2. Type(s):3.2.3.2.4.3. Speed at which cut-off starts under full load (2): r/min3.2.3.2.4.4. Maximum no-load speed (2): r/min3.2.3.2.4.5. Idling speed (2): r/min3.2.3.3Cold-start system3.2.3.3.1. Make(s):3.2.3.3.2. Type(s):3.2.3.3.3. Description:3.2.4. Valve timing3.2.4.1. Maximum lift and angles of opening and closing in relation to top dead centre or equivalent data:3.2.4.2. Reference clearances and/or setting ranges (1)